Be based on the design that special check provides contrail of PRO/E three-dimensional conduit

1 spare parts is designed to spare parts of three-dimensional contrail tubing, want to apply umbriferous method 2 times to found curve of contrail of a scanning above all, and 2 when 2 times umbriferous place needs sectional graphs had better divide a pace to be founded beforehand, it is OK to should use a side only when 2 times umbriferous curve paints sectional picture, design and revise of dimensional contrail in order to facilitate. Next, scanning gives appearance bulk piece. If scan commonly method cannot compose builds a feature, can use advanced function -- compose of scanning compound method builds a feature, jump over all dots intermediate, draw only initiative with terminus 2 identical sectional graphs are OK. Decreasing before cutting inside data, save the part for one temporarily file, this spare parts uses at preform antrum cut. Then, method of compound of same use scanning is decreased cut conduit interior hole, complete the structural design of other again, save the part for one formal document, spare parts. When using the spare parts document that has designed formerly, if bulk interior has cut material through decreasing, must found curved surface to close exit, fill entity, ability can be used at what check provides preform to be cut. 2.

The design principle that 2 check have preform to design preform is to be able to include temporarily document part, motherboard and check are specific OK applying soldering methodological join. 2.

3 combination and cut model antrum uses package module above all, will temporarily spare parts and preform are assembled together by the requirement. Next, the advanced function of use component module cuts a check to have bodily form accent, the process is as follows: C→ of Cut Out of → of Omponent → Adv Utils [choose should implement the preform part that cuts a processing to its] → Done Sel → [consult to cut provenance manage to choose spare parts -- temporarily spare parts] → Done Sel → [if temporarily standard feature is in the other on the spare parts preform, choose Copy(duplicate) , choose Reference (to consult otherwise) can] → Done right now, the preform spare parts in package module and spare parts module is already synchronous cut with temporarily the housing that the spare parts agrees completely, check is specific the housing that go up. 2.

4 perfect check provide a design (craft structure details is designed) still need to provide preform to make farther design to check in spare parts module. Decrease cut redundant material above all, the method of use drawing excises circumjacent and redundant material, decrease the oblique plane material that cuts conduit tail end again. When the material that excises cant of conduit tail end, need founds temporarily careless draw datum plane, reuse decreases the method that cuts material to excise redundant material, the check after cutting down is specific. To find the cent with specific check area, must found flank above all video, should found flank video need founds umbriferous used curved surface. Copy of → of Create → Surface | Done → [choose Surf&Bnd (curved surface and border) option, the method that chooses with inquiry chooses surface of conduit either interior] → [inquire two end panel that select conduit serve as attrib border face respectively, right now, conduit interior eliminates all appearances outside two end by pitch on] Ok of → of Done of → of Done of → Done Sel → , curved surface is founded finish. Seek profile Silhouette (flank of → of Trim of → of video Create → Surface is video) | Done → [the curved surface that on the choice one pace founds] → [the umbriferous direction: that chooses umbriferous outline to cut down? ≡ Zuo face] → points to the section that wants reservation, this exemple chooses to withhold underside curved surface, flank is finished to be founded videoly namely after deciding. Check is specific coping and flank are video the distance of foul line, need left and right sides of 1 ～ 2mm commonly, need uses the method that becomes sectional to scan to found cut curved surface. → of New of → of Create → Surface Advanced | Done → Var Sec Swp | Done → NrmToOriginTraj | → of Bndry Chain of → of Done → Selec Traj [choose: of primitive scanning trochoid? ≡ sleeves  as concubine of an emperor is the? that seek You, appoint initial drop by the graph] No Join of → Done → | → of Bndry Chain of → of Selec Traj of Done → → [: of trochoid of choice X vector? ≡ sleeves  as concubine of an emperor is No Join of → of Done of → of the?] that seek You | Open Ends of → of Done → Done | Done scale is sectional, among them dimension 1.

The 5 top that require for place namely are apart from, and going along with pours horn to be founded together, the destination that adds A of straight line segment is to be founded complete decrease cut curved surface, the end points that notices one part line segment must restrain the initial drop in 2 scanning beam to go up respectively, the curved surface after finishing. Group of face of use curved surface is decreased cut Use Quilt of → of → Cut of upside material Create | Solid | Done → [the curved surface that on the choice one pace founds, appoint by the requirement decrease cut way] → Ok puts the other feature such as curved surface and curve into the layer, obstruct, result. Part of final conduit of craft structure design is unsuited whole journey detects, can choose a key only paragraph detect, will not need to detect the material purify of section, provide to check again undertake necessary craft construction is designed, finishing finally check is provided. 3 epilogue use the cuts a function to design check to provide method of package, it is direct it is with the spare parts be excised of material consult model, need not intervene artificially, have high accuracy, efficient wait for a characteristic. Actually, this method applies to check of contrail of design space conduit to provide not only, and, still apply to design different curved surface (like housing kind gold of spare parts, Ban kind spare parts) appearance check is provided, also can use at tool to design, it is method of a kind of current three-dimensional visible design. CNC Milling CNC Machining